![]() ![]() Until then, you can rely on timed-dry and other non-automatic functions that don’t use the cycling thermostat. To fix this problem, you will need to replace the cycling thermostat inside your dryer in order to restore your auto-dry function. Therefore, if the cycling thermostat is faulty or stops working while the dryer is running, the auto-dry signal is never sent and your dryer will just keep tumbling. The dryer waits for a signal from the cycling thermostat to tell it when the auto-dry phase is complete. The thermostat is supposed to sense when your clothes have reached the ideal temperature and dryness. The cycling thermostat is used for the auto-dry setting. 5) Faulty Cycling Thermostat Dryer Never Stops Spinning on Auto-Dry From there, you can replace the wires, the harness, or the wired assembly to repair the problem. The first challenge is to find where the wire harness was damaged or became faulty. If the wires fuse or are damaged, this can lead to effectively skipping a failsafe or circuit that would normally shut off the dryer. This can happen when there’s a power surge that occurs near one of the key wire harnesses. It is rare but possible that the wiring between your dryer components may have shorted out. 4) Shorted Out Wiring Harness Dryer Spins Without Responding to Timer or Settings To get your dryer back in working order, you’ll need to replace the dryer timer switch assembly. This can result in your dryer tumbling forever in whatever setting it was left or broke in.Īs a temporary fix, manually turn the dryer knob to the next ‘off’ position. If that motor goes out, not only does the knob not turn but the dryer setting doesn’t change either. This is done with a very small motor that pushes the knob around the dial. You may have noticed that the knob turns itself forward to the next “off” position once the dryer is started. If you have a dryer timer of the turning knob variety, there’s another way that this could result in an infinite spin until the door is open. 3) Timer Knob Does Not Turn Timer Knob Doesn’t Turn to Off, Drum Keeps Spinning Indefinitely Don’t worry about the specific part that is fused, simply replace the entire assembly to ensure best results when you repair the dryer. The dryer timer will either be inside the control panel or behind the back panel of the dryer. If this is true, you will need to replace your dryer timer. However, these contacts channel a lot of electricity, and a power surge can sometimes result in a timer cycle contact to fuse in the “on” position so that further action from the timer has no effect. When the timer switches to “off” the cycle contacts release, breaking the current and turning the dryer off. This controls the timer cycle contacts which turn an and off to control the dryer. Many dryers have a twisting timer knob that tells the dryer how long to run, how hot, and when to stop. 2) Timer Cycle Fused On Dryer Doesn’t Stop When the Timer is Over ![]() Reattach the wires, then the mounting screws, then close up the top panel and try your dryer again. Remove the mounting screws and disconnect the wire harness, then install an identical door switch by reversing the process. From here, you’ll be able to access the door switch that tells the dryer when the door is opened or closed. Start by unplugging the dryer and removing the top panel. You’ll need to replace the dryer door switch. However, if the spinning continues after you open the door, this is likely to be trouble with the door switch. Most of the time, and with most of these causes, the dryer will spin indefinitely until the door is opened, at which point the spinning will stop. Do not stick your hand into the motor-spun drum while it is spinning. This is a rare problem that is both fascinating and mildly dangerous. The first and niftiest error is when your dryer keeps on tumbling after the door is open. 1) Door Switch Unresponsive The Drum Keeps Spinning When the Door is Open Dryers are designed to stop tumbling when the door opens or when anything malfunctions, so why this eternal spin? There are six possible reasons why a dryer won’t stop spinning after the door is opened or the timer goes off. ![]() A dryer that keeps spinning past the finished timer or even spinning while the door is still open can cause some pretty serious confusion. One of these rare exceptions is when your dryer won’t stop tumbling. However, sometimes these fail-safes don’t work correctly and an appliance does something truly strange. It’s important for appliances to have a failsafe mechanism built into nearly every system so that if something fails, the appliance stops working instead of continuing to work to catastrophic effect. Appliances tend to fail into an off state, meaning that they don’t do the things they should rather than doing things they shouldn’t.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |